Skip to content

UDO Audio Super 6 firmware

UDO Audio active Device launched 2020
Get alerts for new Super 6 firmware
Free · one message per release

Latest firmware

1.6
released 20 Dec 2024
Download firmware from udo-audio.com

What's new in 1.6

• Enable RBN-1 Intelligent pitch and expression integration (Only relevant for RBN-1 users) Try it: - Connect RBN-1 Ribbon Controller to Expression Pedal input - Power ON whilst holding button P6 ("PED/CV") an LED flourish will show the mode has been entered and will repeat every power cycle as a reminder that the Expression Pedal input is in Pitch Ribbon Mode. - Press and hold a key and move your finger on the ribbon surface to experience smooth pitch expression - Mapping the PED/CV source (now the ribbon) to any destination in the mod matrix will disconnect it from intelligent pitch control - Clearing the Mod Matrix (SHIFT->CLEAR) will re-connect the RBN-1 to the intelligent pitch control - To exit Pitch Ribbon Mode and return to normal Expression Pedal mode, press and hold MANUAL for >5s to reset global settings.

Last checked 18 Nov 2026

What you get with a free account

  • An alert the day a new Super 6 firmware ships, by email, Telegram or push
  • Your whole rig in one place, with the version each device is on
  • Used and new Reverb prices for your gear
  • A public rig page to share, if you want one

We check UDO Audio's official download page for the UDO Audio Super 6 every day. One message per release. No spam, no newsletter.

Sign in, it’s free →

How to update the UDO Audio Super 6

Download the firmware folder from the Super 6 Support & Downloads page. Power the Super 6 off, then hold SHIFT while powering it on and keep holding until the progress LEDs cycle and SHIFT keeps blinking (bootloader mode); release SHIFT. Connect the Super 6 to your computer via USB: it appears as a drive named SUPER6-BOOT. Delete any old .bin file on that drive (on a Mac, also empty the Trash), then copy the new firmware .bin file to the drive and wait until the copy has finished. Disconnect the USB cable, power the synth off, wait a few seconds and power it back on; it may run its tuning routine for a minute or two. Do not power off or unplug USB during the transfer.

Just for reference. For complete and up-to-date instructions, always refer to the manufacturer's official firmware page.

Sign in to see Reverb prices →

UDO Audio Super 6 firmware update history

5 releases since Feb 2021, roughly one every 12 months.

Changelogs summarised from the manufacturer's release notes.

Version 1.6 — 20 Dec 2024

Release notes for this version are listed above.

Version 1.4 — 24 Sep 2024

• "AT->BEND" Slide potentiometer remapping for ST49 SUper 6 Models - For users of the ST49 kit, When LFO2 mode set to ON, Bend amount DDS and VCF sliders control depth of poly aftertouch to pitch and filter cutoff respectively. Pitch bend lever range is defaulted to +/-2 semitones

Version 0.30 — 10 Jan 2022

Patches to 0.27 • Foot Pedal (Expression Pedal) Range Doubled • Can't load SEQ 14 or 16 and can't select MIDI Channel 14 bugfix • Behaviour when no firmware file detected improved • Keyboard Octave saved with patch (Desktop only ignores octave and resets it to middle octave) • Drift function bugfix for Desktop users • Analog Input Gain Setting bugfix for Desktop users • Made more robust behaviour when PATCH disk unlocked for writing by PC/MAC

Version 0.27 — 15 Nov 2021

New in this release: • USB MIDI Try it: - Connect the USB cable to your computer. In your DAW, choose "SUPER6" from the list of MIDI connections and enjoy. Note midi channel mode defaults to "omni" (receive on all channels) until a specific channel is selected. • CC and/or NRPN transmit and receive from all controls* • Dramatic increase in resolution & precision of knob and fader controls & dynamic smoothing • High resolution smoothing and interpolation of incoming MIDI CC & NRPN control change messages • Fully variable Voltage Controlled Highpass Filter Try it: - Set HPF to FIX. Press SHIFT, adjusting CUTOFF will now adjust the Highpass filter cutoff in HPF FIX mode. Exit SHIFT mode to return to adjusting the Lowpass filter cutoff. To hear the effect clearly, play notes in the lower registers (with some bass!) • Start/Stop (& optional Song Position Pointer) incoming MIDI messages responded to - Greatly improved External Clock Sync behaviour generally • Added Decay Hold phase to envelope generators ENV1 and ENV2 (Desktop and KB) Try it: - Set up a sound with SUSTAIN and DECAY around 50% setting on each envelope so you can clearly hear the decay phase. Press SHIFT then adjust DECAY fader. This will adjust the delay after the attack peak is released before the decay phase is entered. The control ranges from 0ms to 5 seconds. • Pan spread control in 12-voice mode Try it: - In 12-voice mode (Binaural OFF) adjust (LFO1) LR PHASE control to adjust pan spread depth • New hold mode in Arpeggiator, latches notes on all key off, updates and does not add while playing Try it: - With the arpeggiator ON, using the sustain pedal or HOLD button, notes will continuously update while at least 1 note is held. When all notes are released simmultanously, the last held pattern will latch. Pressing a new chord will flush the held notes and play the new pattern [...]

Version 0.26 — 17 Feb 2021

New in this release: • Faster Amplitude envelope attack times. An extra 15% of travel has been added at the bottom range of the ENV2 ATTACK slider reducing minimum ENV2 attack times without affecting stored patches • Waveforms pack 2 can be stored on the synth alongside "waveforms" Try it: - Hold PATCH and power cycle the synth to unlock the patch disk "SUPER6" - Download waveforms pack 2 to your PC or MAC from www.udo-audio.com/support - Extract the .zip file on your PC or MAC (not on the Super 6!) and rename the extracted folder "waveforms" to "alt_waveforms" - Connect the SUPER6 to your computer via the USB cable - Copy the alt_waveforms folder to the patch disk "SUPER6" in the root directory - When done, you may need to power cycle the synth - To access the alt_waveforms, select a waveform on the Super 6, pressing the PATCH or BANK button again will cycle between the two banks. The PATCH or BANK LED will blink to indicate the alt_waveforms folder is selected • Super randomisation feature called DRIFT. Subtle dynamic wavering of parameters to add subtle to extreme movement and detuning Try it: - New init_patch.s6 has subtle randomisation on some parameters. Note the almost inaudible but very pleasing movement of oscillators. Particularly nice on complex waves in Super mode. - In SHIFT mode, dial in the amount of parameter movement using the PW [DETUNE] fader. Static phases at 0, sounds broken at 10. • +6dB output level boost. Corresponding increase in SNR by +6dB. - Please note, some patches with extreme settings may now experience clipping distortion regardless of "MASTER VOLUME" setting, simply reduce "ENV LEVEL" control by a small amount if this happens. Fixed: • VCA Bleed in SOLO and LEGATO modes at extreme of ENV2 LEVEL control removed • MIDI Out sometimes requiring change of command type fixed • VCA "Blip" when changing from loud to soft playing with DYNAMICS selected removed [...]

Tracked in 4 rigs on FW//RADAR.

UDO Audio Super 6 firmware FAQ

What is the latest firmware for the UDO Audio Super 6?

The latest firmware for the UDO Audio Super 6 is version 1.6, released on 20 Dec 2024. FW//RADAR last checked UDO Audio's official page on 18 Nov 2026.

How do I update the UDO Audio Super 6?

Download the firmware folder from the Super 6 Support & Downloads page. Power the Super 6 off, then hold SHIFT while powering it on and keep holding until the progress LEDs cycle and SHIFT keeps blinking (bootloader mode); release SHIFT. Full instructions on UDO Audio's official firmware page.

Where can I download UDO Audio Super 6 firmware and drivers?

Directly from UDO Audio's official firmware page — FW//RADAR links to the source and never hosts firmware files. Official firmware page →

Where can I find the UDO Audio Super 6 manual?

The official UDO Audio user manual is a PDF hosted on cdn.prod.website-files.com. UDO Audio Super 6 user manual (PDF) →

View on Reverb →