The iii firmware runs on 2022 and later grids (including grid one and grid zero); 2020-2021 and earlier editions cannot be updated to it.
1. Check the date printed on the corner of the circuit board to pick the right file: iii-grid-2022.uf2, iii-grid-one.uf2 or iii-grid-zero.uf2 (download from the monome iii releases page).
2. Remove the bottom screws and locate the golden pushbutton near the USB port.
3. Hold the button while connecting the grid to your computer: a USB drive appears.
4. Copy the .uf2 file to the drive. It unmounts immediately after copying (a macOS warning is harmless).
5. Disconnect and refit the screws, placing the spacers first.
The iii firmware can toggle between iii and monome/serial (serialosc) modes, so the grid keeps working with norns and serialosc apps.
Already running iii? You do not need to open the grid again: reboot it into bootloader mode from the diii browser app (monome.org/diii) and copy the .uf2 as in step 4. If a beta firmware was installed before, run fs_reformat() (or click reformat in diii) and restart the grid afterwards.
9 releases since Dec 2024, roughly one every 2 months.
Changelogs summarised from the manufacturer's release notes.
Version 1.1.2 — 18 Apr 2026
Version 1.1.1 — 24 Mar 2026
Version 1.1.0 — 22 Mar 2026
Version 250201 — 1 Feb 2025
note: arc has the newest firmware shipped with the device, so there's no need to update until the next version is ready.
- FIX metro now counts up (like norns)
- NEW `device_id()` returns device name
- FIX serial buffer increased, allowing much larger prints (up to 4k)
- NEW slew.allstop()
- FIX serialosc now ignores device in iii mode
- NEW slew lua lib
- NEW metro allocator
- FIX pset_read empty slot
- FIX metro count set to 15 (number of hardware metros available)
see repo for new `slew.lua` example and other examples have fixed metro syntax (see `metro.lua`)
slew uses a single metro, but you can run a bunch of slews on this one instance. the time grain is set to 10ms.
- NEW `grid_led_rel(x,y,delta,zmin,zmax)` -- `zmin` and `zmax` optional, these clamp the range post-delta
- NEW `grid_led_get(x,y)` returns the value
- EXPERIMENTAL: with usb descriptors to evade serialosc in iii mode (in-progress, not complete)
- EXPERIMENTAL: `pset_read(n)` returns table stored at flash position `n`
- EXPERIMENTAL: `pset_write(n,table)` writes `table` to flash position `n`
the `rel` and `get` functions allow for some very low-code interactions which reduce the need for boilerplate when needs are simple.
`pset` functions need a bit more design work. keep in mind that these tables have no awareness of who (which script) wrote them or if the tables will be valid for the current script. my working solution (not yet implemented) is to reserve a metadata slot with what-script-is-now and valid-slots etc.
- NEW changed mode-switch flash reset: hold for 2 seconds when booting into iii mode to erase script
- NEW grid_size_x() and grid_size_y()
- FIX script size set to 32k
- NEW ^^b command to reboot into bootloader mode
- NEW lua commands: round, linlin, wrap, clamp
- FIX grid key detection
- FIX grid key and led functions now 1-indexed (like norns/etc)
The latest firmware for the monome grid is version 1.1.2, released on 18 Apr 2026. FW//RADAR last checked monome's official page on 15 Nov 2026.
How do I update the monome grid?
The iii firmware runs on 2022 and later grids (including grid one and grid zero); 2020-2021 and earlier editions cannot be updated to it. 1. Full instructions on monome's official firmware page.
Where can I download monome grid firmware and drivers?
Directly from monome's official firmware page — FW//RADAR links to the source and never hosts firmware files. Official firmware page →